Supro statesman schematic

General discussion area for tube amps.

Moderators: pompeiisneaks, Colossal

Post Reply
Iquester
Posts: 2
Joined: Mon Jul 05, 2010 5:36 pm

Supro statesman schematic

Post by Iquester »

Someone was looking for this hard to find schematic for a Supro Statesman / Gretsch Fury. I have one I can email.
User avatar
KT66
Posts: 301
Joined: Thu Jan 20, 2005 11:52 am
Location: Puyallup WA

Re: Supro statesman schematic

Post by KT66 »

How 'bout just posting it ?
Ryan

Music is the best. F.Z.

http://Classictubeamps.com
Iquester
Posts: 2
Joined: Mon Jul 05, 2010 5:36 pm

schematic

Post by Iquester »

Here it is.
You do not have the required permissions to view the files attached to this post.
Andy Le Blanc
Posts: 2582
Joined: Sat Dec 22, 2007 1:16 am
Location: central Maine

Re: Supro statesman schematic

Post by Andy Le Blanc »

paraphase driving 4 6L6, verb and trem, thats neat. A paraphase has
plenty of gain to push on pair 6l6 into clip, pretty early too.
A quartet must roar...
lazymaryamps
User avatar
Structo
Posts: 15446
Joined: Wed Oct 17, 2007 1:01 am
Location: Oregon

Re: Supro statesman schematic

Post by Structo »

Interesting with the two OT's.
Sort of like the first JTM 45/100 amps.
Tom

Don't let that smoke out!
Cliff Schecht
Posts: 2629
Joined: Wed Dec 30, 2009 7:32 am
Location: Austin
Contact:

Re: Supro statesman schematic

Post by Cliff Schecht »

What a waste of an amp. 'Wreck it and be done with it.


Just kidding! >:)



The dual OT trick is cool and probably gives this amp a helluva wallop in the bass department (assuming it's voiced well). Can you get a decent amount of distortion out of it? I would hope so with that many tubes shoved inside ;).
Cliff Schecht - Circuit P.I.
Markusv
Posts: 393
Joined: Wed Dec 21, 2005 3:16 pm
Location: Toronto, Canada (yes it's friggin cold!)

Re: Supro statesman schematic

Post by Markusv »

I'm actually trying to do the very same OT thing with an amp on the bench right now

I have an old Radio console amp that ran a quad of 25L6's in stereo
The OT's have an unusual pri:sec ratio- really not suitable for anything else but the original tubes

So I decided to make an amp with 2 completely separate preamps, PI's an Output sections including one OT for each amp. The plan is then to run this "stereo setup" into the same output jack

So I see now that it can be done with basically just the Primary Centre tap sharing the B+ voltage and then the Secondaries paralleled?

BTW this will be a low powered amp (given the output tubes): An AC 30 ish Pentode preamp thing one side and a 5D3 on the other side

Markus V
.........Now where did I put it?
User avatar
KT66
Posts: 301
Joined: Thu Jan 20, 2005 11:52 am
Location: Puyallup WA

Re: Supro statesman schematic

Post by KT66 »

This circuit has a lot of the typical Valco stuff going on in it like their standard paraphase and typical plate and cathode topology, but there is some unusual stuff for them going on here - like the SS FWB, the 6973 reverb driver, a switchable bright cap and the quartet with 2 OTs. The standby function just silences the amp with phase cancellation, but you get a little light to let you know it! Valco high end !

Anyway, thanks for sharing. In honor of the free exchange of info here is my redraw of the coveted Supro 1624T. It's nothing special really, but much sought after.

Cliff wrote :
'Wreck it and be done with it.
Now that's an idea, a wreck with a paraphase ! I'll work on it and then get back to you all. :lol:
You do not have the required permissions to view the files attached to this post.
Ryan

Music is the best. F.Z.

http://Classictubeamps.com
Post Reply