Pre-Etched PCB's Available

Aharon · Post by **Aharon** » Sat May 12, 2007 2:11 pm

Sorry for the silly question,I haven't been to the forum in a while,what build are these for,where's the documentation like stuffing guides and schems?
Thanks and sorry again......
Aharon

Funkalicousgroove · Post by **Funkalicousgroove** » Mon May 14, 2007 5:10 pm

Uhh, these are to build an overdrive special.

They fit the chassis that I sold a while back and will be offering again in the future.

as far as stuffing guides, they are pretty self explanatory, but if you need them I can provide photo's.

sorry for the confusion.....

Aharon · Post by **Aharon** » Mon May 14, 2007 9:41 pm

Thanks Funk.......I was the confused one.
Aharon

Funkalicousgroove · Post by **Funkalicousgroove** » Tue May 15, 2007 2:14 pm

No worries, lemme know if you need any.

Normster · Post by **Normster** » Wed May 16, 2007 4:43 am

Got the boards today. They look funktastic!!!

thanks again!

Funkalicousgroove · Post by **Funkalicousgroove** » Wed May 16, 2007 2:27 pm

GREAT!!

BTW, I use a keystone 1559-2 Turrett in the relay boards, that way it's easy to get 2 or 3 leads in.

galtjunk · Post by **galtjunk** » Mon Nov 12, 2007 4:54 pm

I can't find the 1559-2 turrets anywhere.
I checked Mouser, Newark and Digikey and no one stocks them.
Where can I get some?

heisthl · Post by **heisthl** » Mon Nov 12, 2007 5:38 pm

Funkalicousgroove · Post by **Funkalicousgroove** » Mon Nov 12, 2007 5:40 pm

I wish I got this earlier, I'd have sent some with your strain reliefs.

You can also use small eyelets if you prefer.

Funkalicousgroove · Post by **Funkalicousgroove** » Mon Nov 12, 2007 5:53 pm

mouser p/n 534-1559

galtjunk · Post by **galtjunk** » Tue Nov 13, 2007 12:51 pm

Thanks, I found them. The last time I looked they showed as a non stocked item. Now they are showing stocked.

I've always used turrets so I am unfamiliar with eyelets.
Are the eyelets for the PC Boards and the preamp board 1/8 x .093 (534-43)?

Now I am all out of excuses so I guess I'll have to get started.

Time to make the donuts!

Funkalicousgroove · Post by **Funkalicousgroove** » Tue Nov 13, 2007 3:02 pm

Yes sir.

they also make eyelets that fit those relay boards too if you prefer.

dragonbat13 · Post by **dragonbat13** » Tue Nov 13, 2007 4:08 pm

I know these are for an ODS. I am gathering up parts for a D lite that will be built in a brown note chassis. Will I need this set for the d lite? Maybe just some of the boards. OF course I would buy the whole set for just the boards I need?

jaysg · Post by **jaysg** » Tue Nov 13, 2007 6:34 pm

Stupid question perhaps...what do you mean by "pre" etched? Do they need to be dipped in something?

Tube Amp Archive

Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available

Re: Pre-Etched PCB's Available